Fault code · VW · Audi · SEAT · Škoda · Cupra

B201A00: Check software version management

B201A00 is one of the most common Volkswagen Group fault codes after a part is replaced, updated or unlocked outside a dealer. It means the car no longer matches its factory record. Here's what causes it and how it's cleared properly.

By Harshit Vadgama, automotive engineer · Updated

In short

B201A00 means a control unit's software or coding no longer matches what the Volkswagen Group factory record says the car should have. It usually appears after a module is replaced or updated, or after a feature such as CarPlay is activated outside a dealer. The proper fix is an online SVM run in ODIS, which updates the record and clears the code for good.

CodeB201A00 (older scanners: 1555 / B201A)
TextCheck / checking software version management
Usually stored in5F Information Electronics (MIB2, MIB3), also other modules after replacement
Proper fixSVM in ODIS with online access: Software Version Management → Adapting software
Remote?Yes, with an interface and laptop at the car

What B201A00 means

Every Volkswagen Group car has a record at the factory listing which control units, software versions and coding it should have. That system is called Software Version Management (SVM). When a module reports a software version or coding that doesn't match that record, it stores B201A00 "Check software version management".

It is not a hardware fault. Nothing is broken. The car is telling you that its electronics and its factory record have drifted apart.

What usually triggers it

  • Infotainment replaced or updated. Volkswagen published a service bulletin for exactly this: after an MIB2 infotainment unit (J794) is replaced or updated, B201A can be stored, and the fix is an SVM software adaptation.
  • A feature unlocked outside the dealer. Owners regularly find B201A00 in module 5F after CarPlay or App-Connect was activated by a third party.
  • Firmware or map updates on head units and virtual cockpits.
  • A new or used control unit fitted in any module, especially before it was SVM coded.

Is it a problem?

On infotainment units B201A00 often has no visible symptom, so many owners just leave it. Two things are worth knowing. First, it stays in the fault memory and comes back after clearing, because the mismatch is still there. Second, when a module's factory record is out of date, a later dealer SVM run can overwrite coding that was done offline. If the code appears in a module that controls driving or assistance functions, get it checked rather than ignored.

The two ways people deal with it

Workaround (MIB2 only)Adaptation "confirmation of installation change" with a calculated value. Hides the code; the factory record stays wrong.
Proper fix (all modules)Online SVM in ODIS. The record is updated, software and coding are aligned, and the code doesn't come back.

The workaround is popular on forums and fine as a stop-gap on an MIB2 head unit. It doesn't help with B201A00 in other modules, and it doesn't protect your changes from being undone. SVM is what a dealer would do, and it's what I do remotely. See SVM coding explained for how it works.

What a remote SVM session looks like

  1. You send a full scan (or I take one at the start) and your VIN.
  2. I check which modules report B201A00 and why: a swap, an update or an activation.
  3. ODIS compares the car with the factory record online and applies the correct software, coding and parameters.
  4. Fault memory is cleared, the car is rescanned and the function you care about (CarPlay, for example) is tested.

At the car you need a Windows laptop, a VAS 6154 or J2534 interface, a battery charger and a stable internet connection. Voltage matters during programming: see why battery voltage matters.

If CarPlay was activated by someone else

That's the most common story behind this code. The activation itself usually still works. What's missing is the SVM step that makes the car's record match. If you want the activation to survive future dealer visits, an SVM run is the clean way to finish it. If CarPlay isn't active yet, see CarPlay activation.

Frequently asked questions

Can VCDS or OBDeleven clear B201A00?

They can clear it, but it comes back while the mismatch exists. On MIB2 head units a calculated adaptation value can hide it. Only an online SVM run in ODIS updates the factory record and fixes the cause.

Is B201A00 dangerous?

Usually not. It means software or coding doesn't match the factory record, not that a part is broken. In modules that control driving or assistance functions it should still be checked.

Why did B201A00 appear after CarPlay activation?

The activation changed the head unit, but the factory record wasn't updated. The module reports the difference as B201A00. An SVM run aligns the record.

Can B201A00 be fixed remotely?

Yes. With an interface, laptop, charger and internet at the car, SVM runs online through ODIS just as it does at a dealer.

Sources